DreamBox DM 100 Technical Details & Pictures

[lolazoca]

How to upload softcam.*** file to DM100

How to upload softcam.*** file to DM100
by Sn4TCHBuRG3R

This "how to" assumes you have already installed the UART USB COM driver and the LoaderChEditor.exe
If you haven't installed the above then check out the following threads for files and instructions.

OK, here goes, I've attached some pictures of the LoaderChEditor process at the bottom to help newbies

1. Connect USB A-B lead from PC to DM100 and connect power lead to DM100
2. Load the 'LoaderChEditor.exe'
3. Click on 'Conn' Button' to connect to DM100
4. Click on 'Tools' --> 'Connect Status' --> 'Upload to STB'
5. An Open File box will open, from the file type drop down box select "*** files .***"
6. Select the folder that holds your SoftCam.*** file, click on the "softcam.***" file and click 'Open'

You will now see a box appear that displays the following message, "Now trying to connect to STB wait...'
This box will disappear after a few seconds and the softcam file will be loaded to the receiver.

You will see another message appear, "Writing to the flash, please do not disconnect"
Once the file has been loaded sucessfully you'll get another message box appear to say, "Complete"
Press OK to close the message box.

7. Now click on the 'D-Con' button to disconnect the DM100 from the LoaderChEditor application.
8. Power off the receiver by disconnecting the power lead from the back to reboot.

Finished.

[basemoi]

Originally Posted by lolazoca

Little picture...

\\

hello
i update the box with 126 but i can not see any emu instaled
what is wrong?

can anyone help me??

[lolazoca]

How to upload Firmware file to DM100

This "how to" assumes you have already installed the UART USB COM driver and the LoaderChEditor.exe
If you haven't installed the above then check out the following threads for files and instructions.

OK, here goes, I've attached some pictures of the LoaderChEditor process below to help newbies ;-)

1. Connect USB A-B lead from PC to DM100 and connect power lead to DM100.
2. Load the 'LoaderChEditor.exe'
3. Click on 'Tools' --> 'COM Settings' Select the COM port number the UART Serial Port driver is configured to.
4. Click on 'Conn' Button' to connect to DM100
5. Click on 'Up' Button to upload new firmware.
6. An Open File box will open, from the file type drop down box select "BIN File .BIN"
7. Select the folder that holds your "DM100_Vxxx_firmware.bin" file, click on the "DM100_Vxxx_firmware.bin" file and click 'Open'

You will now see a box appear that displays the following message, "Reset your STB'
Remove the power lead from the DM100 then reconnect the power lead to the DM100.

You will see another message appear, "Writing to the flash, please do not disconnect"
There are 2 stages to the flash process, so wait for stage 1/2 to complete then stage 2/2 to complete.
Don't worry if stage 2 hangs for 30 seconds before the progress bar starts to move, this is normal.

Once the file has been loaded sucessfully you'll get another message box appear to say, "Complete"
Press OK to close the message box.

8. Now click on the 'D-Con' button to disconnect the DM100 from the LoaderChEditor application.
9. Power off the receiver by disconnecting the power lead from the back to reboot.
10. Switch on DM100 and select 'Factory Reset' from the DM100 on screen menu.

Finished.

[lolazoca]

Firmware
Release V018F from 29.09.2008

[soylis]

how to connect FTP via ethernet?or web interface?

[lolazoca]

HowTo "Flaschen der DM100"

[lolazoca]

NEW DM100 Loader / Channel Editor 30.10.08

Version 2.3
Update 30.10.08

[dreambox2008]

Hi I want to know where can I find the patches för SmartCard reader for CONAX, I have the DM-100-S.

Thanx!

Best Regards

dreambox2008

[lolazoca]

Dm100s Main V0130 20081120

We are happy to release new s/w ver1.30.Thank you for really hard job for all of our members!

In this version,
- Updated CCCAM, sorry for late update!
- Modified softcam key editor
- Changed subtitle
- Fixed aspect ratio
- Fixed diseqc,c

[lolazoca]

Firmware v1.32

fixed:
- Diseqc,
- CCCAM server

Notice: 
when you update new firmware, you have do ‘factory reset’,
And all user setting will be erased. We will find a way to keep
‘user setting’ after updating new firmware without ‘factory reset’.